Welcome to the company ! we have many years of professional experience !
rsdgj@pyzyrsd.com +86 513525609655

full automatic cyclone desander manufacturer distributor

Established in 2001, Puyang Zhong Yuan Restar Petroleum Equipment Co.,Ltd, “RSD” for short, is Henan’s high-tech enterprise with intellectual property advantages and independent legal person qualification. With registered capital of RMB 50 million, the Company has two subsidiaries-Henan Restar Separation Equipment Technology Co., Ltd We are mainly specialized in R&D, production and service of various intelligent separation and control systems in oil&gas drilling,engineering environmental protection and mining industries.We always take the lead in Chinese market shares of drilling fluid shale shaker for many years. Our products have been exported more than 20 countries and always extensively praised by customers. We are Class I network supplier of Sinopec,CNPC and CNOOC and registered supplier of ONGC, OIL India,KOC. High quality and international standard products make us gain many Large-scale drilling fluids recycling systems for Saudi Aramco and Gazprom projects.

Certificate of Honor

CONTACT US

Customer satisfaction is our first goal!

Phone

+86 513525609655

E-Mail

rsdgj@pyzyrsd.com

Address

Road West, North Branch, Jingkai Road, Puyang City

full automatic cyclone desander manufacturer distributor
BACKUP SUMP PUMP - Owner's Manual
BACKUP SUMP PUMP - Owner's Manual

vertical float switch or electrical switch. Tethered float switch takes more sump pit space and might interfere with the emergency pump. Manually operate your primary sump pump and pump out the water in your sump pit. Do not let the pump run dry. This will damage the pump. Disconnect the primary sump pump power source before attempting to install.

Superior Pump 92341 - Things You Need to Know (2021 Deep ...
Superior Pump 92341 - Things You Need to Know (2021 Deep ...

After setting up, plug the cord of the ,pump, into the piggyback plug of the ,float switch,, then plug in the outlet. If the ,pump, runs, this means that the ,switch, is ,stuck, in the wrong position and will not work properly. The ,pump, should turn on by itself when the water rises, causing the ,switch, to ,float, in an upright position.

Troubleshooting | Zoeller
Troubleshooting | Zoeller

18/7/2017, · Before pulling the ,pump,, reduce setting on pressure ,switch, to see if ,pump, shuts off. If it does, worn parts are probably at fault. Pull ,pump, and replace worn components. ,Pump, becomes ,sand, locked. If the fuses blow while the ,pump, is operating, ,sand, or grit may have become wedged in the impeller, causing the rotor to lock. To check this, pull the ...

This pump series has a built in thermal protection switch ...
This pump series has a built in thermal protection switch ...

8. Connect the ,pump, power with a 120V GFCI on a dedicated 15-Amp circuit, and do not allow the cord to interfere with the ,float control, motion. 9. If the ,pump, turns on, check the ,float switch, and move to the low position if necessary. 10. Once installation is complete, check the functionality by filling the sump with water using a bucket or hose.

Sewage grinder pumps / sewage ejector pump FAQs ...
Sewage grinder pumps / sewage ejector pump FAQs ...

2., check, for a jammed or, stuck float switch, at the, pump, 3. check that the, pump, motor hasn't been jammed, and, perhaps damaged by an inappropriate solid being drawn into the pump impeller, such as tampons, diapers, dental floss. 4. check that the type, and, model of pump is properly-matched to how yours is being used.

SUBMERSIBLE SUMP PUMP - Star Water Systems
SUBMERSIBLE SUMP PUMP - Star Water Systems

Pump runs continuously. 1. Float is stuck in the ‘on’ position. 1. Make sure the float can move freely. 2. Float switch is defective. 2. Replace pump. Pump runs but delivers little water. 1. Pump is air-locked. 1. Clean out vent hole in discharge pipe. 2. Vertical pumping distance is too high. 2. Reduce the vertical distance to correspond with the performance

What Causes a Boat to Sink and What You Should Know
What Causes a Boat to Sink and What You Should Know

The most common way for a boat to sink is from a faulty bilge ,pump, not working correctly, or a bilge ,pump float switch, becoming ,stuck, with grit and grime. Here are some other common mistakes that might sink your boat:

BEFORE OPERATING OR INSTALLING THIS PUMP READ THIS …
BEFORE OPERATING OR INSTALLING THIS PUMP READ THIS …

(Note: ,pump, will operate more ef fi ciently in an 18" diameter sump.) 4) ,Float Switch,: (where applicable) The fl oat ,switch, (if so equipped) is sealed and factory adjusted to be suitable for most sumps. Be sure that the fl oat has adequate clearance and cannot become ,stuck, …

Understanding the Warnings & Alarms
Understanding the Warnings & Alarms

This can occur for many different reasons. Either the float is stuck in the up position, there is a mechanical problem with the pump, or there is a problem with the plumbing connections. Please refer to the Troubleshooting Guide on the back. Dual Float Switch The dual float switch contains two large floating rings enclosed within a protective cage.

Troubleshooting | Zoeller
Troubleshooting | Zoeller

Before pulling the ,pump,, reduce setting on pressure ,switch, to see if ,pump, shuts off. If it does, worn parts are probably at fault. Pull ,pump, and replace worn components. ,Pump, becomes ,sand, locked. If the fuses blow while the ,pump, is operating, ,sand, or grit may have become wedged in the impeller, causing the rotor to lock. To check this, pull the ,pump,.

Chat Online Inquiry Email

Business cooperation

+86 513525609655

Company address

Road West, North Branch, Jingkai Road, Puyang City